SSH (Secure Shell) provides secure management of network devices. By using SSH, you establish a secure connection to a network device that you access, and your data is sent in encrypted form.
The SSH (Secure Shell) protocol, which uses for encrypted data transmission, uses 22 port number and provides machine control management by providing a remote connection.
To configure Cisco Routers for the first time, you must use the console connection. After connecting to the device using the console, you can assign an IP address, and then enable Telnet or SSH to manage over LAN/WAN.
How to Configure SSH on Cisco Router
For security reasons, configuring Routers with Telnet over LAN or WAN is not recommended. It is recommended that you configure the SSH connection instead of Telnet.
Because SSH provides a secure connection, it encrypts your data and allows you to securely manage your network.
How to Enable SSH in Cisco Router
After completing the preparations for SSH configuration with GNS3, follow the steps below.
Now open the GNS3 program and type a name for the new project.
Drag and drop the previously added Router into the workspace.
Add a Switch and Host to the workspace and wire the network devices.
After creating a small network topology, open the Virtual Network Editor of the VMware virtualization program and configure a VMnet for the virtual machine.
Create a VMnet in the Virtual Network Editor program, and then assign the IP address to it from the network and share center settings on your Host as shown in the image below.
Type an IP block for VMnet3 in the virtual editor, select Host-Only and click OK.
Configure the virtual machine’s network adapter setting to Custom (VMnet3).
Configure the virtual machine’s network adapter setting to Custom (VMnet3). Click Start / Resume all nodes to run the router.
To enable SSH after running the router, open the CLI prompt and perform the following commands in order.
R1# conf t R1(config)# interface fastethernet0/0 R1(config-if)# ip address 192.168.8.1 255.255.255.0 R1(config-if)# no shutdown R1(config-if)# exit R1(config)#ip domain-name sysnettechsolutions.com R1(config)#crypto key generate rsa general-keys modulus 1024 The name for the keys will be: R1.sysnettechsolutions.com % The key modulus size is 1024 bits % Generating 1024 bit RSA keys, keys will be non-exportable...[OK] R1(config)# ip ssh time-out 15 R1(config)# ip ssh authentication-retries 2 R1(config)# ip ssh version 2 R1(config)# username cisco privilege 15 password cisco123 R1(config)# line vty 0 4 R1(config-line)# login local R1(config-line)# privilege level 15 R1(config-line)# transport input ssh R1(config-line)# exit R1(config)# end R1# wr
Open the Putty program on your virtual computer and enter the IP address of the Router’s FastEthernet0/0 interface in the IP address section, and enter 22 in the Port number section and click the Open button.
In the Putty security alert window, click Yes.
The SSH connection to the Router will be successfully established as in the following image.
Type the username you created in Login as and press Enter.
Enter the user password (cisco123) you created in the Password section and press Enter.
Once connected to the Router with SSH, you can now easily manage your device over LAN or WAN.
To view SSH sessions on the router, type the show line command in Privileged Mode and press Enter.
You can check the Telnet or SSH connections from the image below.
To check the SSH version, execute the show ssh command in privileged configuration mode.
You can check that the SSH version is 2.0 in the show command output.
You can use [ ssh -l (User Name) (Router IP Address) ] at the command prompt to initiate an SSH session on a PC or other router on the network.
To connect from Router to Router, execute the ssh -l cisco 192.168.8.1 command, and then type your password and press Enter.
You can see SSH sessions again when you use the show ssh command.
Use the show line command to display the current session.
You can use the exit command to terminate the SSH connection.
How to Connect from Router to Router with SSH Protocol ⇒ Video
You can watch the video below to make an SSH connection from the virtual machine to the Router using the simulator program and also subscribe to our YouTube channel to support us!
In this article, we have examined how to use SSH on Router with a network simulator program. Thanks for following us!