What is Spanning Tree Protocol in Switching? | Understanding STP Protocol – In today’s computer networks, network redundancy is very important. The continuity performance of network devices that are well configured on the network increases at the maximum level. Connecting the switches with more than one network cable means network redundancy.
What is Spanning Tree Protocol in Switching? | Understanding STP Protocol

What is Spanning Tree Protocol in Switching? | Understanding STP Protocol

What is Spanning Tree Protocol in Switching? | Understanding STP Protocol

In a well-designed network, an error has become almost impossible. The reason for this is the design and development of backup networks. Therefore, if an institution that provides a good service or market reputation experiences inability to provide services to its customers, it will lead to loss of customers and reliability and also commercial loss.

Layer 2 Switches used for data transmission on the network create a Loop on the network when backup ties are not properly configured. For example; You have connected two Switches with two network cables but you have not configured them with STP. This is to create a random backup network.

In fact, the purpose here is to automatically switch on the other cable in case of a fault in a cable. If we give more detailed information, it is the shortest way to transmit the frames over the fastest link.

In the previous article, we have given detailed information about the network redundancy and also mentioned the problems that arise in the network backup process. The biggest problem of these problems is Loop. We can also say Broadcast Storm.

The following image is a small network topology that forms Loop;

What is Spanning Tree Protocol in Switching? | Understanding STP Protocol

Our Recommendation

You can purchase “Cisco Switching” from Amazon.

If we explain the picture above, let’s assume that they are computers connected to the Switch. Because these computers do not have MAC addresses, they broadcast (ff:ff:ff:ff:ff:ff) over the network via the ARP protocol. Switch2, receiving the broadcast frame, transmits all frames except for the interface it receives.

As a result, Switch2 will transmit the Broadcast frame back to Switch1, and ARP traffic will be generated because the computer received the Broadcast frame will send the Broadcast frame in the same way. Therefore, a loop will occur on the network and the Loop will continue as long as one of the two switches is not turned off. You can prevent the loop by removing one of the two cables connected to the switches.

Well, why is this Broadcast framework going to last forever? Because Ethernet Frames have not a TTL (Time to Live) value.

At this point, STP (Spanning Tree Protocol) will come into play.

How STP Protocol Works?

STP (Spanning Tree Protocol) chooses the best path as well as preventing loops on the network. Although the operational logic of the STP protocol is mainly mixed, it is very easy to configure on Switches.

The STP protocol uses the Spanning Tree Algorithm (STA) algorithm to avoid Loops.

Let’s briefly describe how the STP Protocol works;

1. The STP Protocol backs up (standby) or blocks certain interfaces configured on the switch as backup connections.
2. The STP Protocol puts the interfaces for the latest devices in the Forwarding mode.
3. The STP protocol transmits the packet by determining the most suitable route in case of failure of the forwarding path.

After the STP Protocol is enabled on the switches, the STA algorithm configures a map of the Switches. The STA algorithm uses some terms to determine the backup path or the best path for transmission of the data packet.

When we look at the image below, we see that 3 Switches are connected to each other. In a Spanning Tree Protocol-configured network, Switches send packets called BPDUs between themselves. The switch that is selected as the Root Bridge sends BPDU (Bridge Protocol Data Units) packets to every other switch on the network every 2 seconds.

What is Spanning Tree Protocol in Switching? | Understanding STP Protocol

A BPDU framework contains the following information;

1. Source Switch Identity Information
2. Source Switch Port Information
3. Root Bridge Outbound Path Total Cost
4. Maximum Data Packet Timer Value
5. Hello Package Information

As explained in the above image, BPDU frames will be sent between Switches every 2 seconds. If you like, you can change the default hello packages. How was the Bridge ID value set for the selected Switch as the Root Bridge?

How Does STP Protocol Select Root Bridge?

In fact, all Switches are Root Bridge and the default Priority value of all Switches is 32768.

When setting the Bridge ID value, the MAC Address and Priority value are considered. If all switches have the same default priority value, the Bridge ID is determined by looking at the MAC addresses. In the above view, the smallest MAC address is AAA and the Switch-1 with the smallest MAC address will have the best Bridge ID value and therefore will be the Root Bridge.

The interfaces defined as Root Bridge always function as Designated and this always means Forwarding.

In the following image, Switch-1 is the Root Bridge and Designated ports are also indicated by the letter “D”.

What is Spanning Tree Protocol in Switching? | Understanding STP Protocol

How Does STP Protocol Select Designated and Root Ports?

In Spanning Tree Protocol configuration, the shortest path to the Root Bridge Switch is called the Root Port. Therefore, the Switch-2 and Switch-3 Ethernet0 / 0 interfaces above will be configured as Root Ports.

Spanning Tree Root Port is used to select Path Cost. Under normal conditions, the Path Costs assumed by the IEEE are calculated as follows when calculating with the Bandwidth / 1000 formula.

BandwidthPath Cost
4 Mbps250
10 Mbps100
16 Mbps62
45 Mbps39
100 Mbps19
155 Mbps14
622 Mbps6
1 Gbps4
10 Gbps2

In addition, each Switch connection must have one Root Port. In the following example, the closest interfaces to the Root Bridge are designated as Root Ports.

What is Spanning Tree Protocol in Switching? | Understanding STP Protocol

After reviewing the Root Ports, we will look at Switch-2 and Switch-3 Ethernet1/0 interfaces.

How Does STP Protocol Select Designated and Non-Designated Ports?

When the Designated Port is selected, the MAC Address and Priority values are examined. If the priority values of both switches are equal, the MAC addresses for the Designated Port will be checked.

In the following example, when Switch-2 is selected as the Designated Port, the other Switch will be selected as Non-Designated/Blocked to prevent looping.

What is Spanning Tree Protocol in Switching? | Understanding STP Protocol

Once Designated and Non-Designated/Blocked Ports are identified, Loop will no longer occur in our network. In the above images, the connections between Switches have the same Path Cost values. Therefore, these ports may vary in a network that spans more than one Switch. Also, the selected Port-Orange will be Non-Designated/Blocked.

Understanding Spanning Tree Protocol (STP) in Cisco Packet Tracer

To better understand the Spanning-Tree protocol, we will examine the STP protocol details by adding 4 Switches in the Cisco Packet Tracer program.

What is Spanning Tree Protocol in Switching? | Understanding STP Protocol

When we examine the network topology above, we can see that all Switches have the same priority values. Therefore, the STP protocol will select the Switch with the lowest Bridge ID value as the Root Bridge by evaluating the MAC address when selecting the Root Bridge.

1. Once the Root Bridge is selected, the interfaces bound to its ports will be Designated Ports. Because the links to both Bridge Switch are in the root state. The next step is to select Root Ports.

2. If Root Ports is selected, the Path Cost to the Root Bridge Switch is considered. If Path Costs are equal, Switch0 and Switch3 will be selected as Root Port. For example; If the path cost value between Switch3 and Switch2 was 19, the connection to the Root Bridge from Swich3 would enter the Non-Designated/Blocked state.

3. Once the Root Ports have been defined, the Switch1 bindings will be configured. If so, the outgoing Path Cost is calculated from the Swictch1 Root Bridge. If Path Cost equals (4 + 4), Switch1 MAC Address and Priority are examined. According to the topology above, the Priority values are equal and therefore the MAC Addresses are considered. Switch1, Switch0, and Switch3 look at Bridge ID values and set the lowest value Switch0 as the Root Port.

Thereafter, a single interface remains and this interface will be configured as Non-Designated / Blocked to prevent loops. As a result, the STP protocol designs the network map by sending and receiving BPDU frames on the network to and from other switches.

How STP Works? [ Understanding STP Protocol ] ⇒ Video

You can watch how STP works ( Understanding STP Protocol ) and you can also subscribe to our YouTube channel…

  Final Word

What is Spanning Tree Protocol in Switching? | Understanding STP Protocol – On the Network Switches, the STP Protocol is enabled by default and automatically selects the path. However, it is very important to configure the management of the switches on the network manually. Management of Cisco Switch BPDU packages is extremely important in terms of security.

If this article is helpful, send me feedback by commenting! Thanks in advance, take care of yourself!

Also, you can add to browser bookmarks by pressing the CTRL+D to read this article later!

Articles Related to What is Spanning Tree Protocol in Switching? | Understanding STP Protocol

Products Related to What is Spanning Tree Protocol in Switching? | Understanding STP Protocol
Related Products

File Related to What is Spanning Tree Protocol in Switching? | Understanding STP Protocol
Related File
You can download STP configuration configured on Cisco Packet Tracer to your computer…

Leave a Reply

Your email address will not be published. Required fields are marked *

twelve + 19 =