What are The Methods of Switching in Computer Network? – Switches used in computer networks should receive the incoming package in the normal operating principle and transmit it to the target. However, a Switch uses different methods when performing this task.
What are The Methods of Switching in Computer Network?

What are The Methods of Switching in Computer Network?

What are The Methods of Switching in Computer Network?

Computer networks have traditionally been built using Layer 2 and Layer 3 Switches. Switch uses different methods when sending packets on network switching. These methods are very different and completely applied according to the network structure.

Before moving on to the methods of switching, we had discussed what is switch in networking in the previous article.

Our Recommendation

You can purchase “Cisco Small Business Switch SG300” from Amazon.

The Methods of Switching

Switch switching types can be examined under 3 headings. These methods have advantages and disadvantages among themselves. The Store and Forward method, which is the most used and often used by default, is the most common method of switching.

Store and Forward Switching

In this switching method, the entire frame is read and stored in memory before being sent to the destination. The switch controls the integrity of the bits of the frame using the CRC (Cyclic Redundancy Check) mechanism.

If there is no problem in CRC calculation, the Switch will send the frame to the target. Therefore, if there is an error in the CRC computation, the Switch will never send the frame to the destination port.

In the Store and Forward method, the transmission of faulty frames is blocked but creates a high latency time. The Store and Forward method is used in networks designed to prevent errors from happening.

Cut-Through Switching

Although Cut-Through is a fast method, it is not recommended. To transmit a Switch frames using the Cut-Through method immediately, it transmits the frame without performing the CRC calculation. As a result, frames submitted before CRC calculation will be problematic.

Cut-Through Switching is divided into two parts;

1. Fast-Forward Switching

The Fast-Forward method is the fastest method of switching types. The switch will send the target MAC address in the frame to the target port that is read and not read. As a result, there will be no delay in the Fast-Forward switching method. However, since the switch does not perform CRC control on the frame, the frames will be sent as damaged.

However, since the switch does not perform CRC control on the frame, the frames will be sent as damaged. You can use this method in a stable network environment with very few problems.

2. Fragment-Free Switching

In the Fragment-Free method, the Switch controls the first 64 bytes of the frame before transmitting the frame to the destination port. Incoming frames lower than 64 bytes appear as Collision, which is called Runt.

In the Fragment-Free switching method, the first 64 bytes are controlled to prevent conflicts on the network.

The Store-Forward method has the highest latency time, while the Fast-Forward method has the lowest latency time if we are going to make a small comparison by taking both methods.

The delay time of the Fragment-Free method remains between these two methods. Fragment-Free switching works very well in network environments where the collision is very dense.

Adaptive Cut-Through Switching

Most Cisco switches use the Store and Forward method. This is due to the fact that with improved technology and faster frame transmission improvements, frames are transmitted without errors and very fast. In addition, switches that can adapt to the network environment have been developed.

These switches have fast transmission capabilities with low latency. When the switch sends the frame to the destination port, it sends it too fast without CRC checking and the frame is successfully transmitted to the destination without error. With this method, the switch frame forms an error counter in the transmit memory and compares the error rates with the threshold value.

If the frame error counter is greater than the threshold value, the Switch is considered to have performed a number of erroneous operations. As a result, the Switch will immediately return to Store and Forward as it uses an adaptable method. Therefore, when the error counter falls below the counter value, the Switch will immediately return to Fast-Forward.

In short, these types of switches are called Adaptive Cut-Through.

Cisco Switch Basic Configuration ⇒ Video

You can follow up the basic configuration steps of the Cisco Switches by watching the video and you can also subscribe to our YouTube channel…

  Final Word

What are The Methods of Switching in Computer Network? – In this article, we have examined the frame forwarding methods of Switches in detail.

If this article is helpful, send me feedback by commenting! Thanks in advance, take care of yourself!

Also, you can add to browser bookmarks by pressing the CTRL+D to read this article later!

Articles Related to What are The Methods of Switching in Computer Network

Products Related to What are The Methods of Switching in Computer Network
Related Products

Leave a Reply

Your email address will not be published. Required fields are marked *

nine − five =